Category: Studio

Overview and run down of Singer 360 K for Philip

Test performed: full bed stockinet, slip, fair isle, 1×1 mock ribbing.

Sport yarn is the best. Thicker (e.g., worsted yarn – best on every other neelde).

I did not extensively test the knit leaders but all knobs and levels work.

The machine came with some assesories and some I added. I added a set of punch cards. The set is brand new but differs a bit from the original Singer/Studio set. The machine came with some knit leader sheets, and they will be included.

The overveiw is below.

Missing are:

• Oil canister. I do not include old oil on purpose. Please, get a fresh/new oil. The recommended by many machine kntiters is Hoppe’s Elite Gun Oil
• Only one ravel cord in included but any smooth strong yarn can be used
• only one set of point cams (number 15) and yarn separators were included. These are usd for single-motif knitting. This is somewhat advanced technique and if you are proficient enough with just one single motif (two sets are needed to knit two single motifs) you will know by then where to get additional sets. To be honest, I tried single single-motif and it was so challenging that I simply gave up. It is challenging by all the small details needed to kniw a single motif. There are other machines to do it much easier. Plus, I like motifs throughout the whole bed anyways… But with just one set of point cams and yarn separators you will still be able to knit just one single motif.

   

All tools fit into a built-in storage.

The machine itself is in great shape.

There are couple of impercets on the plastic and on the cover.

They are:

• Masking tape stain on the tool box lid

Some writing on the carriage. I wiped it but did not rub too much to avoid damaging already old and potentially brittle plastic.

 

The case and the lid have minor scratches and minor bend. The most prominent is the red stain on the lid.

 

The strip with numbers has some minor staining (seen on video).

 

Video just for you:

 

I also recommend getting this small cast-on comb. (I am not affiliated with them). It makes the cast on so much easier for beginners…

 

Manual and recommended brochures specifically for this machine are here:

(but keep in mind that I am sending you generic punch cards – they might not match the numbers shown in the third brochure).

https://mkmanuals.com/knitmaster-360-260-knitting-machine-manual.html

https://mkmanuals.com/knitmaster-360-260-operation-knitting-machine-manual.html

https://mkmanuals.com/knitmaster-360-260-pattern-book-knitting-machine-manual.html

Please read my other post on overall pros and cons of Singer/Studio knitting machines and 360K model in general.

http://thoughtsandknits.com/2022/09/04/360-for-laura-cleaned-in-august-2022/

http://thoughtsandknits.com/2022/08/07/studio-360-k-memomatci-reported-in-august-2022/

Second Singer Studio 360 Mod restored/cleaned/refurbished in March 2022

http://thoughtsandknits.com/2021/10/13/my-first-singer-360-memomatic-360k/

 

Some pictures as I am putting the whole package together.

Studio (also known as Singer, Silver Reed and Elna) machines are great machines to have for beginners or advanced knitters…They offer a lot of versatility. So far, I had a simple (without any automatic patterning with the exception of manual needle selection) and punch-card Studio machines. Studio 360K appeared on the market in 1980-1982. They are equipped with a 24-stitch patterning mechanism transferred to the needles using the punch-card reader.

The hero of this blog, Studio 360K, has 200 needles. The distance between needles (which is also called a gauge) is 4.5 mm, which is considered a “standard”. The best yarn for this machine is sports weight. Thicker yarns can be kitted on every-other needle.

This particular Studio 360K knitting machine came to me in a pretty decent shape so no major disassembling was required. There was no rust. I removed dust/dirt using a brush from under the bed (I did not disassemble it). I removed all needles and polished them as there was a tiny bit of rust on them where a bad (decomposed) sponge bar was touching them (it is pretty typical for old neglected machines). However, all the needles were inspected individually and I tested them by knitting on a full bed using different techniques. The short answer is – everything looked good. For more justification/information on how I judge it – refer to the youtube video made for this machine. The sponge bar was replaced at the beginning of August 2022. It was only used to test this machine (made three cowls on it – see below).

The carriage was somewhat more sensitive to the combination of yarn and tension than the other machines I refurbished. If possible, I would recommend using new sport weight yarn, wound into cakes, and taking the yarn from the middle of the cake while knitting.

The machine came with no end rails. This is a typical problem for most Studio/Singer machines. These end-rails are rubber, which decomposes with time. Some Singer/Studio machines have metallic end rails but this one had separate rubber ones. They typically tend to decompose due to time and fall off. So, initially, these rubber end-rails were still present but while I was using the machine they fell off since they already showed a lot of cracking and deterioration. These end rails are also not very critical pieces and the machine will work fine without them. They are important when knitting on all 200 needles. But even in this case, if you slow down the carriage on the last 10-20 needles and don’t let the carriage slide too far, you will be ok. These end rails are needed to prevent drums from mis-patterning if the carriage is moved too far from the bed.

I typically do not include end-rails with my refurbished machines because most knitters do not use the full bed – only some needles in the middle. However, I felt that because this machine is sensitive to tension, it could be relatively easy for a new knitter to accidentally slide the machine from the bed. So, I installed the new Installed end rails. The carriage without them did not run as smoothly. FYI: if these decompose and fall again, the new ones simply snap on but the lid needs to be removed. Contact me if you need help with that.

BEFORE:                                                  AFTER:

I did not extensively test the knit leaders because I do all my calculations myself. But all buttons turn freely and the paper advances as the carriage moves back and forth. The video shows this as well.

The machine came to me without the original punch cards. I purchased a set so this machine has all accessories. Some of the punch cards correspond to the original set and some are different (more exciting, in my opinion).

The machine also DID not come with a hard copy of the manual but it can be found here (totally free). This and this brochures are also typically included with the package for 360K. they cover some knitting techniques as well as garment shaping. I found them very useful when I knitted my sweater last year.

All the tools are present, including replacement needles. If more are needed, I recommend purchasing the replacement needles here. Only one set of unraveling cord, card snaps, point cam, and yarn separators are included. The yarn separators and point cams are needed to knit 2 single motifs. To be honest, a single motif on punchcard machines requires a lot of skills. So, by the time the user decided to knit two single motifs (where two sets of these are needed), this knitter would be considered advanced and will either know where to get these parts or will switch to an electronic machine (single motif on electronic machines is so easy!!!). The carriage lock (accessory number 2) was not supplied with the original setup. So, I ordered a 3D printed one specifically for this machine. The card guide was also missing (accessory number 18). But I included a large knitting needle that I used while testing this setup.

This carriage runs on the bed a bit tighter than my other 360k. It is also very sensitive to tension. Make sure the yarn flows really REALLY smoothly and that the cake/bobbin/cone is right underneath the tension mast.

The machine has several cosmetic imperfections. They are:

1. The discoloration on the carriage. It is not affecting its function. Probably a previous owner attached a sticker to it and the plastic around it became darker with time.
2. Shipped end by the end rail. It also does not affect the functioning of the machine.
3. A couple of scoff marks on the knit leader card advancing mechanism.

I also replaced the two front top panels (they are slightly lighter than the middle one – see the last picture above). They were severely cracked and needed to be totally replaced.

To learn about the general pros and cons of Studio/Singer 360K, please, refer to my previous post.

When I test machines, I really like to knit something in the process. So, I am making these wide pieces of knitted fabric, which I then convert to cows/hoods/neck warmers. Below are the cowls that I made while testing this machine:

You can see me making these in this video (no instructions though – yet!)

All these are going to charity to support the Happy Hats Maryland project to supply 1000 hats and scarves to those in need in my county.

Happy knitting with this machine!!

This post is in progress as I am editing it while cleaning the machine.

Replaed two main plastic consoles since they were broken. Took these parts from identical (but for parts) Studio 360K. Cleaned very thoroughly inside the mechanism (but I did not disassle it since there was no rust and overall everything looks in good shape and everything moed freey).

This machine was a rare find since the patterning drums did not shut stuck and moved freely. I suspect this machine was not used a lot since even during cleaning I did not see a lot of fold grime.

Replaced sponge bar, inspected all needs, polished and visually chcked. Also checked all needles in action (see my video on a full-bed knitting) to make sure the needles not just looked good but also functioned well.

Well, this caption is so strangely phrased because the very first Singer 321 came with a Spanish manual and with the knitting terms written on the machine in Spanish 😊 But both machines are in great shape and are workhorses no matter in what language their menu is.

I thoroughly cleaned this machine. I would like all my buyers to be aware that I only completely disassemble machines that are in very VERY rough shape or severely rusted.

Checked all needles, replaced sponge bar and tested how it knits tuck stitch, slip stitch, fair isle and stockinet. I did it on the whole bed to make sure all needles function properly. The machine is capable of patterning using the old-fashioned punch-card technology.

A little bit of history: Singer/Studio 321 machines were introduced in1972 and were the second earliest model capable of patterning with 24-stitch punch cards. It is a standard (4.5 mm) gauge machine with 200 needles. So, this machine is 50 years old!!

It is still beautiful and this particular model has barely any age-related discoloration.

The machine came with all accessories with couple of exceptions:

• Box to pack all the tools is missing. It did not come with this machine. I will pack all the tools in a sturdy bubble-enforced plastic bag. All other accessories are included.
• The carriage lock is unfortunately missing too. The lock secures the carriage on the metal bed during storage and transport. I will secure the carriage with zip ties to make sure it does not slide.

Pros and Cons of this particular machine:

Pros:

• Typically, these machines have rubber end rails to keep the carriage from sliding from the bed and mis-patterning as a result. These end rails are made from rubber, which degrades with time (years). But not in this machine: you don’t have to worry about them. This machine has metal end-rails, which will stay forever.

Cons:

• No built in leader. It is not a deal breaker for me – I calculate and keep track of all my patterns and forms myself.
• This model does not come with a lace carriage
• The carriage does not have a release lever – if the carriage gets stuck during knitting, you will have to do remove the sinker plate and then move the carriage.

The rest of pros and cons is typical for all other singer/studio knitting machines with punch card mechanism, namely:

General Pros and Cons for Singer/Studio machine with punch card patterning mechanism:

Pros

• The patterning drums make it very easy to move the machine. They engage with the punch card mechanism very nicely without much noise.
• The manual is very well-written and I was able to follow the instructions with ease and to learn all the techniques.
• Easy-to find replacement needles since these models are relatively “newer” ones. I get mine on Aliexpress.
• The tools are pretty standard and are pretty interchangible with other models. Aliexpress also sells them.
• I found that putting this machine to storage and opening and closing is much easier than multiple brother machines I had a chance to struggle with. There is a very clear schematic on the cover with the order of how placing the parts together. I found this extremely helpful as putting these machines away is often a big frustrating struggle.

The cons are:

• no timing belt, which might make the carriage movements somewhat hard depending on your tension and knitting pattern and technique. It was not a problem for me at all.
• The most significant flow in my mind is that the patterning drums often get stuck if not oiled regularly, especially when not used for a very long time or put into storage (I restored already two OTHER machines where the drums were simply shut… They needed soak in an oil bath and some heavy-duty disassembling). To avoid this problem, put some light oil regularly on the patterning drums. Lucky for me, this machine had the drums in excellent shape

Check out my freshly posted youtube video: https://youtu.be/te0sV0o78FI

This is what I knitted while I tested this machine: a two-in-one cowl/scarf and a head cover. I love multipurpose things.

This machine is a beauty despite some of its minor flaws (Like missing pieces). It has beautiful color combination and barely any discoloration of the plastic.

This wonderful machine was made in 1970^th and, I think, it was the first model to include a built-in knit leader. Like most standard gauge knitting machines, the Singer 326 has 200 needles spaced 4.5 mm apart. It has a built-in row counter, punch-card reading mechanism for automatic patterning using a punch-card reading mechanism. I gave this machine a thorough clean. The carriage was also deep-cleaned and serviced and all knobs and levers and functions were thoroughly tested. Drums on the carriage move freely.

It comes with all accessories including (numbers are going in the order as they are listed in the manual).

1) magic cams,

2) point cams,

3) separators,

4) box to store and transport all tools,

5) replacement knitting needles,

6) brush to clean the machine,

8) weaving arm,

9) container with oil

10) crochet hook

11) tapestry needle,

12) ravel cord for cast-on and to use as one-row intermediate level during waste-yarn knitting,

13) round brushes for tuck knitting (I already installed them on the sinking plate for you),

14) card snaps to clip the patterning cards together,

15) stitch scale (simply a set of rulers to help with knit-leader and stitch counting),

16) gauge scale to count stitches and your gauge on a swatch,

17) and 18) tension mast assembly,

19) weights to hang on the ends of your knitted piece,

20) set of stitch transfer tools,

21) tappet tool,

22) clamps to secure the machine to the table. On this particular machine with these particular clamps, it is somewhat hard to attach them to the bed– the bed needs to be at a certain angle. But with enough wiggle, they will fit in.

23) carriage lock to secure the carriage during transport and storage

24) card guide,

25) needle pusher and needle selector,

26) set of punchcards: the original set was supposed to include 20 cards but this machine came with only 19. Card #19 is missing,

27) a set of pattern paper with some patterns for knit-leader (also known as knit contour).

All accessories fit nicely in the box.

A couple of minor accessories are missing:

• Only two-point cams are included. These are used for single-motif fair isle knitting. By the time you are ready to knit a single motif, you will be an expert in knitting and will know where to find the second pair (if you need to knit two single motifs).
• Name paper: it was included with the originally new machine so the owners can write their names to mark the machine as belonging to them.
• Ravel cord: any silky or acrylic yarn will work

I tested the machine on single -and double-color slip-stitch, tuck-stitch and fair isle techniques. On

this machine, the ‘fair isle’ is marked as a ”knit-in on the carriage. Old terminology? Hm..

I knitted on a full bed to make sure all needles were not bent and without any other defects. I knitted a double-sided reversible cowl on this machine.

A disclaimer: I typically completely disassemble machines only if they show a significant amount of rust or damage. The old screws often don’t make it threw frequent screwing and unscrewing. And these screws are hard to find in regular hardware stores.

A couple of things to keep in mind about Singer/Studio machines in general. It seems that table clamps for Singer/Studio are slightly different than those from Brother machines. Singer clamps have a slightly longer top part. However, not all Singer/Studio machines have clamps with flat tops (some have large screw-top fasteners).

Some Singer/Studio machines have metallic end rails but this one had separate rubber ones. They typically tend to decompose due to time and fall off. So, initially, these rubber end-rails were still present but while I was using the machine they fell off since they already showed a lot of cracking and deterioration. These end rails are also not very critical pieces and the machine will work fine without them. They are important when knitting on all 200 needles. But even in this case, if you slow down the carriage on the last 10-20 needles and don’t let the carriage slide too far, you will be ok. These end rails are needed to prevent drums from mispatterning if the carriage is moved too far from the bed.

Some of the pictures above were taken prior to a complete cleanup – so the machine looks dusty on some. But it is much cleaner and happier now because it is a working horse and I hope you will adopt it for your knitting projects.

I did not extensively test the knit leaders because I do all my calculations myself. But all buttons turn freely.

The tuck brushes, according to the manual, need to be installed when knitting tuck-stitch patterns. In the video I created for this machine, I demonstrated that these brushes can stay on the sinker when knitting slip-stitch, stockinet, and fair-isle. Also, tuck-stitch can be knitted without these brushes (also shown in my video).

The sinker plate comes with already installed tuck-brushes and honestly, I do not recommend removing them as it is rather painful to put them back.

Overall, I was very pleased with this machine: it absolutely does not show its age and knits wonderfully! I hope you will be able to enjoy it soon too and knit a lot of wonderful garments! Talking about age: it might have some super minor scratches on the bed but everything else looks great.

And last, but not least, pros and cons:

Pros:

• The patterning drums make it very easy to move the machine. They engage with the punch card mechanism very nicely without much noise.
• The manual is very well-written and I was able to follow the instructions with ease and to learn all the techniques.
• Easy to find replacement needles since these models are relatively “newer” ones. I get mine on Aliexpress.
• The tools are pretty standard and are pretty interchangeable with other models. Aliexpress also sells them.
• Some might find having the built-in knit-leaders very handy: there is no need to have a separate long setup lying around – in this setup, all fit into one carrier box
• I found that putting this machine to storage and opening and closing is much easier than multiple brother machines I had a chance to struggle with. There is a very clear schematic on the cover with the order of how to place the parts together. I found this extremely helpful as putting these machines away is often a big frustrating struggle.

The cons are:

• no timing belt, which might make the carriage movements somewhat hard depending on your tension and knitting pattern and technique. It was not a problem for me at all.
• The most significant flow in my mind is that the patterning drums often get stuck if not oiled regularly, especially when not used for a very long time or put into storage (I restored already two OTHER machines where the drums were simply shut… They needed to be soaked in an oil bath and some heavy-duty disassembling). To avoid this problem, put some light oil regularly on the patterning drums. Lucky for me, this machine had the drums in excellent shape
• This model does not come with a lace carriage
• The carriage does not have a release lever – if the carriage gets stuck during knitting, you will have to remove the sinker plate and then move the carriage.

So, I did everything for this machine so you can simply take it out of the box and start knitting (cleaned, tested, replaced sponge bar, and checked all needles). I hope this machine will soon find you 🙂